asus m2n61-ar memory when add more memory will not boot

#Asus m2n61 ar memory when add more memory will not boot upgrade
#Asus m2n61 ar memory when add more memory will not boot windows

'CONNECTING a POWER SUPPLY TO an ATX MOTHERBOARD WITH DIFFERENT PIN NUMBERS'

It hints that -5V is needed only by (old) motherboards that have ISA slots: The following webpage has a lot of relevant info. (The corresponding pin on the 24pin connector is labeled 'NC' meaning 'no connection.') Note that the old (verson 1) 20pin connector provides -5V but the new (version 2) 24pin connector doesn't. 'COMPUTER POWER SUPPLY: PINOUT, CABLES, CONNECTORS' The following webpage shows the pinouts for ATX power connectors: I think Freelancer1988 is in error about -5V being provided by modern power supplies.

Capacitors on the motherboard and inside the power supply show no visible signs of failure: no leaked electrolyte, no bulges.) The dvd drive works okay in a different computer.

The computer seems stable now with the case open and dvd drive removed. The problems began after a thunderstorm that caused lights to flicker off the UPS is a cheap standby unit. The PD Doctor diagnostics that came pre-installed showed faults with the 1394 port so I disabled the 1394 in Device Manager. Attempting to boot from a CD in the dvd drive fails and causes the dvd drive to be omitted from the BIOS' list of available drives.

#Asus m2n61 ar memory when add more memory will not boot windows

(Problem description: Windows Vista freezes occasionally. (If the specs depend on the specific model of Slimline, a chart showing specs of each model could be on page 1, or linked from page 1.) I think the answers to those questions would be useful on page 1 of this thread. Is an adapter needed to connect a Flex ATX power supply to the 'mini ATX' power socket on the M2N61-AR Acacia motherboard? Is a pin schematic available for the motherboard's power socket that shows the voltage (or signal) of each pin? The webpage below claims the 220w s3505f power supply is compatible with the s3421p and provides -5V:īut some of the power supplies recommended in this Slimline forum thread (FSP FSP270-60LE, Sparkle SPI270LE) don't output -5V.Ģ. Does the new power supply need to provide -5 volts? Googling has turned up vague & conflicting info about compatibility of third party power supplies, so I have a few questions about specs:ġ. (If you're curious for the details, see the end of this post.) My brother's HP Slimline s3421p is 6 years old and may need its power supply replaced or repaired. I would also be upgrading the lone wimpy 92mm(?) internal mount fan inside the case to a stronger one to increase airflow in the case a bit more.Īny suggestions or advice about doing any of this - or should I just buy a new 'regular sized' uATX/microATX case, motherboard, and PSU (mentioned above) and strip my HP Slimline down for parts to build the rest of the non-Slimline-sized system? I'm also assuming that I cannot use the HP motherboard in another case, since it probably has 'non-standard' proprietary connections for various case components such as power/reset, LED indicators, etc. My plan was to modify the system a bit, so that I could mount an regular ATX Enermax Revolution X't ATX 430 Watt Power Supply (w/Motherboard HP slimline PSU adapter) on some rubber feet on the desk directly behind my slimline (since I never move it) and simply run the modular cables necessary into the back on the slimline through the opening where my tiny 220W power supply used to be.

#Asus m2n61 ar memory when add more memory will not boot upgrade

Since the PSU form factor on the HP s5-1414 matches nothing that I know of in the real world (thanks HP!), finding a quality-brand 400w-450w slim form-factor PSU upgrade for this system is all but impossible. It's the AMI 8.07 BIOS with UEFI support. I would hope that my BIOS would be current enough to use a Low-Profile NVidia Geforce 750. Also memtest to check RAM if you haven't already?ĭoes this apply to older Bios HP slimlines only? I'm using a late 2012 HP s5-1414 i3-2130 slimline system w/factory Windows 8. I would try to isolate the fault as usual to a particular compnent by adding removing with ones you know are working. I suppose I'm not knowledgeable enough about the starting steps for this.these steps worked for me on a basic desktop so I'm not sure what is the difference? When I am using a startup disk (either DVD or USB stick) then I get the starting Ubuntu logo but as it starts to load I get to a blinking underscore and it just stays there. I've tried other steps, such as to use GParted to prepare any basic partitions.also hangs. When I go to load Linux (Ubuntu) it just hangs. I bought the hardware for a miniITX unit: all the hardware seems to operate correctly. Not sure what component to remove as I believe they are all likely to be necessary: RAM, chip, power.ĭo you know if there are any links about loading Linux specific to this motherboard? Chry: yes, I reach BIOS and all appears normal.

Asus m2n61-ar memory when add more memory will not boot